X100 AC/DC Manual
4: Sarting X100startup X100 to enter the main interface ( Image 1 ).Showing“Warning and Disclaimer” 2 seconds and will know the copyright and security
4: Sarting X100【NOTE】 Please read Disclaimer before doing anything.Image 3Image 4 Information BarAction Bar6: Enter into main interface after acceptin
Example 1:Choose a set of LiPo battery charging,please follow the below steps:Image 5Step 1: Touch Type( Image 5 ) Enter into the “Type interface”, an
Image 7Step 2: Touch ‘Mode’ icon( Image 7 ) to enter into Mode interface. Please choose battery charge mode ( Image 8 ) and go back to main interfac
Image 9Step 3: Touch Cells icon ( Image 9 ) to enter into Cells interface. Please set battery packs by sliding ( Image 10 ). Touch OK to go back to ma
Image 11Step 4: Touch Current icon ( Image 11 ) to enter into Current inter-face. Please set charge current by sliding ( Image 12 ). Touch OK to go ba
【NOTE】You could use this function after you have set Type/Mode/Cells and Current correctly.Image 13Image 14Step 5: If you often use the same battery,
Image 15Step 6: You could load your previous data according to X100’s load function. Touch Load icon ( Image 15 ) to enter into Load inter-face. Choo
Image 17Step 7: Touch Start icon ( Image 17 ) to enter into Start interface. The system will check battery status automatically. If everything is OK,
Image 19【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 19 ).Image 20【NOTE】 The ch
Example 2: If you want to charge a pack of NiMh battery, please execute the operation as follows:Image 21Step 1: Touch Type icon ( Image 21 ) to ente
Image 23Step 2: Touch Mode icon ( Image 23 ) to enter into Mode interface. Touch Charge icon ( Image 24 ) to go back to main interface and continue s
Image 25Step 3: Touch Cells icon to enter into Cells interface. Please set NiMh battery packs by sliding ( Image 25). Touch OK to go back to main inte
Image 27Step 4: Touch Current icon ( Image 27 ) to enter into Current interface. Please set charge current by sliding ( Image 28 ). Touch OK to go bac
Image 29Step 5: Touch Start icon ( Image 29 ) to enter into Start interface. The charger will check battery status automatically. If everything is OK,
Image 31【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 31 ).Image 32【NOTE】The cha
Example 3: If you want to charge a pack of Pb battery, please execute the operation as follows,Image 33PresentSettingType CellsModeLoad Save Uset Sha
Image 34Step 2: Touch Mode icon ( Image 34 ) to enter into Mode inter-face. Touch Charge icon ( Image 35 ) to go back to main interface and continue s
Image 36Step 3: Touch Cells icon ( Image 36 ) to enter into Cells inter-face. Please set Pb battery packs by sliding ( Image 37 ). Touch OK to go back
Image 38Step 4: Touch Current icon ( Image 38 ) to enter into Current in-terface. Please set charge current by sliding ( Image 39 ). Touch OK to go ba
New Charger X100 Releasedwww.imaxrc.com/X100.htmliM·OS V2.15USB Port32 bit processorA whole new OS system for X100 professional charger with high effi
Image 40Step 5: Touch Start icon ( Image 40 ) to enter into Start interface. The charger will check battery status automatically. If everything is OK,
Image 42【NOTE】The charger will pop-up window when the battery is fully charged. Touch OK to finish charging process ( Image 42 ).Image 43【NOTE】The cha
iM·OS SYSTEM ADVANCED APPLICATIONiM·OS SYSTEM is brand-new software of charger which was Independently research and develop by iMaxRC. It is the first
Touch “Cut off Low Input”( Image 46 ), the information bar on left will skip into setting menu( Image 47 ), touch “OK” after setting done, it will tur
Cut off Low InputCut off Temperature Cut off CapacityCut off TimeLixxCheckTimeNixxDeltaPeakWaste TimeRange of setting:10-24V. Lowest cut off input vol
Backlight LevelBuzzerLanguageBackCycle TimeRange of setting: 1-10, Brightness level.Range of setting: All sounds open, only touch tone closed, All sou
Please follow the instruction to operate your X100 charger, to insure safety of you and charger, and use it easily. Please keep manual within easy rea
·Add: F4 201-205, F518 IDEALAND Baoyuan Road, Baoan, Shenzhen, P.R.C·Tel: +86-755-89830228·Fax: +86-755-29558361·Web: www.imaxrc.comNEVER use X100
All specifications and figures are subject to change without notice. Printed in China © 2013
iM·OS Systemwww.imaxrc.com/X100.htmlTypeLoadCurrentSaveCellsUsetModeStartX100 support more than 6 type batteries LiPo / Lilon / LiFe / NiMh / NiCd /
iM·OS Systemwww.imaxrc.com/X100.htmlLiPoLiIonLiFeNiMHNiCdPbLipo Battery,Single Nominal Voltage: 3.7V,Charge cut-off voltage 4.2V,Discharge cut-off vol
BalanceChargeFastChargeStorageDisChargeLipo balance charge use CC-CV charging way. The charger will balance the battery voltage when charging, this on
X100 Fundamental Functionwww.imaxrc.com/X100.htmlCheckerManual ChargeCycleMeasuring Mode. The charger only collect battery primary port and balance po
X100 is a professional RC model battery charger,please view the manual before using. If you are a fresh man please read this entire operating manual c
Please follow the below steps connecting:1: Please connect the AC power cord with X100 charger, and then plug adapter of power cord into socket.Connec
Kommentare zu diesen Handbüchern